Yesterday some of us went on a little field trip to a couple local scrap yards. We met the people there and learned the ropes of how to do things right and not get hurt while digging for treasure in the piles of stuff they have laying around. Wear gloves, old clothes, safety glasses, and sturdy shoes! Stay away from moving cranes!
Here’s one of the discoveries from yesterday’s trip- explosion proof mercury vapor light fixtures:
A pallet full of explosion proof lamps at the scrap yard.
And here’s what can be done with about an hour to figure out how to get it apart to remove the mercury vapor lamp and ballast and clean it up a little. Another 10 minutes went into installing the hardware, wiring, and a 6W LED bulb. I wouldn’t call it finished yet- the base is crying out for installation of pipes to act as feet, a little more cleanup, and maybe a dimmer switch. Total invested: $18 to get the fixture from the scrap yard, and another $12 for the hardware and LED bulb.
Explosion proof industrial lamp turned into table lamp.
This a follow up post to this one. I’ll list a few more ongoing classes and collaborative build efforts at our space.
This class is required before working in the ceramics and pottery area. It teaches you the general rules of housekeeping and basics of materials used in this process. Class details here.
Polymer Clay Basics
This class is designed to give you an overview of the Polymer Clay process. This medium can be used to make a wide variety of small accessories and jewelry pieces.
Felisha has been introducing the addicting process of wood turning to many makers. The beginner class covers tools, sharpening, turning spindles, basic work holding strategies, and finishing. By the end of the class each person will have completed a bottle stopper! Students actually learn on Felisha’s professional machine at Our Daily Salt. Class details here.
Trash to Cash
Tom had an ingenious scam idea to clean the makerspace. He shows you how to take a pile of junk and determine what has value and how to take it to the scrap yard and get cash for it! The money made from recycling is used to improve the space.
Keep your eyes open for more classes on the mailing list!
If I could summarize a makerspace with one phrase, it would be a, “place to share you skills.” This post lists a few ongoing classes and collaborative build efforts at our space.
Held for the first time last night, Marvin was excellent enough to teach Electronics 101 based on the lectures found here. A lot of our class attendees have can built circuits using existing schematics but don’t always understand the theory. This class hopes to bridge some of that gap. The class will be held every other Monday for the next 3 months. Next class should be on March 2nd at 7PM.
Lance and Chris have taught two Arduino 101 classes in the last 3 months on Saturday mornings using the excellent Digilent chipKIT Uno32 boards donated by Microchip. Details are on the wiki. The class starts from what an Arduino is, helps you with IDE installation, and you upload your first program to blink an LED! Watch out for upcoming 101 classes. I have heard whispers of an 102 offering as well…
Blacksmithing: Make your own Trivet
This class first describes, “What the Hell is a Trivet?” Then over 3 hours Dan walks a beginner through safety, forge operation, and basic blacksmithing. In addition to these awesome skills, you end up with a unique gift for a loved one. More details here.
Glass Etching Workshop
This multi-skill collection class is one of my personal favorites. After Pete’s initial class offering, Lexie has taken on the torch. In this class, you learn how to cut your mask in vinyl. You learn the software and hardware skills required to operate a vinyl cutter. You transfer the vinyl to a glass mug and sand blast the exposed areas. You end up with a beautiful product that also makes a great gift. Class details here.
Tesla Coil Build Club
A few members will start meeting on the second Sunday of each month to make a Singing Solid State Tesla Coil. The build will be based on this style. We’re all looking forward to see what they come up with.
I will list a few more classes in another post. Not to mention, there is so much learning, teaching, and collaboration that goes on every single day. So come on down and learn from us or teach us something.
Well, it would be awesome if I had a sweet drone to fly around so I can take some awesome videos. Even if I had one I’d probably crash it. I don’t have one, but I did get my hands on a sweet Tarot GoPro gimbal. If you didn’t know, gimbals are devices that use active feedback to cancel unwanted pitch and yaw. I’m not a good cameraman, so I need this if I want to take some decent video for a Kickstarter project I’m working on. The gimbal is supposed to take 7-16 volts, but I hooked it up to a power supply at the makerspace and found out that it can function at 5V, which is great since I have some spare USB power banks.
The high tech gimbal hardware was combined with my low-tech “block of wood and random rods I found in the makerspace” technology. This hack took about 20 minutes, and I’m pretty pleased with the results.
I heard a lot about Milwaukee Makerspace while I was in undergrad at UW-Milwaukee. I had complete studio(s) to work in though, so never made it down to the space until after I had graduated. I finally got a membership through work so I could make things for my job.
Why did you decide to join?
I needed access to equipment and knowledgeable people that I was sorely lacking after exiting academia.
What do you do at Milwaukee Makerspace?
I make devices, prototypes, and templates for work. So far I’ve gotten to work with the laser cutter, 3D printers, powder coating equipment, metal shop and finishing areas.
What would you like to tell others about Milwaukee Makerspace?
There’s something for everyone at Makerspace, and there’s always people willing to lend a hand or a brain to get your project done.
What do you plan to work on in the next few weeks?
I’m currently working on a measuring device for work that will help us measure the length and girth of custom garments that are near impossible to accurately measure. I would also like to get back to the jeweler’s bench and get going on a couple of personal projects.
In addition to making things, many of our members like making machines that make things! We should have a functioning vacuum former, a 4’x8′ CNC Router, and a 4’x8′ CNC Plasma Cutter in the the next couple of months. While the vaccum former was acquired from an auction, the other two have been built at the makerspace over the last year and a half from scavenged materials. The frame and the rails for the plasma cutter were used in a perfume bottler in a past life. We can’t wait to see what our members will make from these awesome machines!
A few pictures of the above mentioned equipment can be found below:
So, a few of us got together and backed Nate’s Revision 2 controller kit. The kit came in last week, I picked up a cheap toaster on clearance, and this past weekend we installed the kit into the oven.
From the kit installer’s perspective Nate’s kit couldn’t be simpler. A supplied SSR is inserted in series with the main AC line, and a K-type thermocouple is fed into the oven cavity. Both items connect up to a pre-assembled circuit board and LCD touchscreen.
We fired up the oven and ran it through its paces right from the touch screen. It performed great right away. There were no real issues. I did manage to install the display upside down, but that will take 5 minutes to flip the next time I’m at the space. I just plain ran out of time. Next time I’ll also be able to play a bit with the PC software, but it was great that the controller fired up and ran right away without having to mess with the PC at all.
So now the space has a nice profiling reflow oven! I am looking forward to using it! I know one member already has a board lined up to go this Tuesday (Feb 3rd, 2015). So if you’d like to see it run in person stop on by the space on Tuesday at 7PM!
September 27-28 at Wisconsin State Fair Park, the same weekend as Harvest Fair. Admission is free. Maker Faire Milwaukee's Call for Makers is now open.
Connect with Milwaukee Makerspace
Join our public mailing list to talk with Milwaukee Makers about projects, techniques and more.
Check out some behind the scenes info on our wiki.